Renault Captur Rear Bumper: Fitment, Sensors & Common Damage
On the Captur, a warning before any towbar work — plus why the genuine reversing camera runs on 6V, not the 12V most DIY guides assume.
Opens live listings in a new tab.
OEM Part Number: confirm via VIN
Aftermarket covers: Prasco RN7021071 / Van Wezel 4384540
| Rear bumper covers (aftermarket) | Prasco RN7021071 (Rear, primed, with holes for parking sensors); Prasco RN7021061 (Rear, Colour: black, Grained); Prasco RN7021051 (Rear, Colour: black, Grained, with holes for parking sensors); Van Wezel 4384540 (Rear, Colour: black, without holes for parking sensors, with holes for towing hook, Rough); Van Wezel 4384541 (Rear, Colour: black, with holes for parking sensors, with holes for towing hook, Rough); Van Wezel 4384542 (Rear, with holes for park assist) |
|---|---|
| Lower sections, corners & trims | Prasco RN7021153 (Right Rear, primed); Prasco RN7021154 (Left Rear, primed); Van Wezel 4386534 (Right Rear, primed) |
| Genuine (OE) numbers quoted | None quoted in the catalogue listings — the genuine cover varies by body style, parking sensors and tow bar, so order it against your VIN |
| Fitment notes | Match body style, facelift date and the holes for parking sensors or exhaust trims; covers come primed and need painting to your paint code before fitting. |
Why towbar fitting can upset the Captur's alarm
This is worth taking seriously before booking a towbar installation: one case saw a car's alarm begin triggering unexpectedly immediately after a towbar was fitted, with the garage initially denying responsibility and even cutting and taping over a wire as an improvised attempt to "immobilise" the alarm — which didn't resolve the underlying issue, and the alarm went off again. In the same case, plugging in a trailer afterward revealed the electrics simply didn't work at all. This is a real illustration of how poor towbar wiring work can cause serious, disruptive faults well beyond the towing electrics themselves — worth choosing a reputable, experienced fitter carefully, and worth insisting on a proper diagnosis rather than an improvised workaround if something goes wrong immediately after the work.
Also, not every car of the same nominal trim and model year came with a reversing camera prewired — some need wiring run from scratch through the car, while others already have a connector present simply needing the camera itself connected and the feature activated in the infotainment settings. Checking the boot area and rear light cluster wiring for an existing, unused connector before assuming you need to run entirely new cabling is worth doing first.
What a parking scrape at the back can damage on the Captur
The Renault Captur's rear bumper is rarely just a bumper — parking sensors, a reversing camera housing, and sometimes exhaust trim finishers are commonly built into it, so even minor kerb damage can turn a simple swap into a bigger job.
Watch: replacing itJ87 gen
The job the back panel does
Beyond absorbing minor impacts, the rear bumper on higher trims of the Captur often houses parking sensors, a reversing camera, and sometimes integrated exhaust finishers. A bumper that looks compatible can still be missing the correct cutouts or wiring provisions for your specific trim's equipment.
Generations and Colour| All generations | Pearl White, Diamond Black, Flame Red, Iron Blue |
|---|---|
| Two-tone options | The Captur's signature feature is its two-tone body/roof combinations (e.g. body colour paired with a contrast Mystery Black, Marble Ivory or Planet Grey roof) — a distinctive option not commonly offered on rivals in this class, available on most trims from mid-spec upward |
Opens live listings in a new tab.
These are the same regardless of make or model — see our full Rear Bumper Guide for common damage types, confirming fitment (body style and sensor equipment matter here), and OEM vs aftermarket guidance.
The same part on other modelsThe same part, covered across other Renault models.