Peugeot 108 Front Suspension Strut: Specs, Fitment & Common Faults
On the 108, whether a knock changes with temperature is a useful diagnostic clue — plus a free DIY test for track rod wear.
Opens live listings in a new tab.
OEM Part Number: confirm via VIN
Aftermarket front struts: KYB 332807 / Meyle 40-26
| Front strut / shock absorber (aftermarket) | KYB 332807 (Excel-G, right) / 332808 (left); Meyle 40-26 623 0011 (right) / 0010 (left); Kamoka 2000129 (right) / 2000130 (left); Daco 453935R / 453935L; febi 1002419 (right) / 1002477 (left). All gas, mostly twin-tube. |
|---|---|
| Front lower arm / wishbone (aftermarket) | LH Vaico V42-0849, Delphi TC6889, Meyle 30-16 050 0135/HD (reinforced), Metzger 58209401, Sasic 7470054, TRW JTC4034; RH Vaico V42-0848, Delphi TC6890, Meyle 30-16 050 0136/HD, Metzger 58209502, Sasic 7470055, TRW JTC4035 |
| Top mount / strut bearing (aftermarket) | Sachs 801 042 (left and right); febi 37750 (rolling bearing, dia 45 mm); febi 37771 (left, with ball bearing); Metalcaucho 05513 (rolling bearing); Meyle 40-14 641 0012; KYB SM1930 (kit) |
| Genuine (OE) numbers quoted | Sasic 7470054 LH arm: 1614191480; Sasic 7470055 RH arm: 1614191680; Sachs 801 042 mount: 41741-58J00, 48619-0D010, 48619-0D011, 48619-0H010, 5036 57, 51726-SAA-003, 51726-SAA-013 (non-Peugeot, treat with caution); Kamoka 209185 mount: 5035.C2. |
| Fitment notes | Standard gas twin-tube |
Hot or cold: what the knock's timing says on the 108
A well-documented, useful pattern worth paying attention to: whether a knock gets better or worse as the car warms up during a drive points toward different specific causes. A knock that's prominent when cold and largely disappears after driving for a while often points toward a worn top mount or strut bearing, which behaves differently as the rubber components warm and flex more freely. A knock that instead appears or worsens after around 30 minutes of driving, particularly at slow speeds, has been traced in documented cases to worn steering tie rods rather than the suspension itself — worth mentioning this specific timing pattern to a technician, since it's a useful clue for narrowing down the cause faster than generic trial and error.
Note too that this platform has a well-documented reputation for knocks that survive an initial repair — multiple documented cases describe drop links, top mounts, or ball joints being replaced without the noise actually resolving, sometimes requiring several visits and multiple components addressed before the actual cause is found. This isn't necessarily a sign of an incompetent garage; it reflects a stubborn platform characteristic where more than one worn component can be masking or mimicking another's symptoms. Real cost figures worth knowing: top mount replacement has been quoted around £60 in parts plus £80 labour on the 208 specifically.
Everything the suspension handles on the 108, mostly unnoticed
On the Peugeot 108, nothing from the road surface reaches the cabin without first passing through these components, so their wear tends to blur into vague, hard-to-place symptoms instead of one obvious failure. Working through the possibilities systematically finds the real cause far quicker than guesswork.
Watch: replacing it108 is the Aygo II/C1 II twin; this video is the first-gen car, same layout
Inside a front corner
The strut assembly at the front of the Peugeot 108 does double duty — housing both the damper and the spring's mounting point. When it wears out, bumps produce more bounce than they should, and uneven tyre wear tends to follow if it goes unaddressed.
Opens live listings in a new tab.
These are the same regardless of make or model — see our full Front Suspension Strut Guide for symptoms of worn bushings and ball joints, confirming fitment against your VIN, and rubber vs polyurethane guidance.
The same part on other modelsThe same part, covered across other Peugeot models.